Haier is one of the top brands when it comes to manufacturing electronics or electrical devices. Washing machines are one of their most popular products that are being used all around the world. No one can deny the level of benefits that come along with buying a Haier washing machine but issues can occur as this is an electronic product just like any other. The good thing is that the machine displays a specific error code for each different type of issue in the machine.
For your convenience and better experience of using Haier washing machines, we have gathered all the error codes, their causes, and solutions so that you can resolve the issue instead of panicking. If you are unable to resolve the error even after implementing the suggested solution, it is better to call professional help from a technician and get your washing machine serviced.
Haier washing machine error Err1, Error 1
Cause:
- This error occurs when the door of the washing machine is opened.
- Something is preventing the door from closing or too much dirt in the door latches.
- The door locking mechanism is broken, damaged, or completely defective.
Solution:
- Close the door if it was opened previously.
- Check and ensure that no cloth or another object is perverting the door from closing.
- Verify that the locking mechanism is working fine. If not, replace it.
Haier washing machine error Err2, Error 2
Cause:
- This error code indicates that the water is not draining properly.
- A fault in the drain pump or drain pump filter.
- Leaked or blocked drain hose.
Solution:
- Check the drain pump to make sure it is clean and nothing is clogging it.
- Take the pump filters out and clean them to remove dirt buildup.
- Check drain hoses for any leaks or kinks. If damaged, replace the hose.
Haier washing machine error Err3, Error 3
Cause:
- The temperature sensor is faulty.
- The wiring of the temperature sensor is broken or not correctly connected.
Solution:
- Seek professional help from a technician to check the temperature sensor, its wiring and connections.
Haier washing machine error Err4, Error 4
Cause:
- The error occurs if the heating coil is faulty or completely damaged.
- Too many clothes in the washer that the washing machine is unable to reach the set temperature within the required period.
Solution:
- Check the heating coil and replace it if needed.
- Turn OFF the washing machine. Take some clothes out and then turn it ON again.
- If still getting errors, seek professional help for maintenance and service of the washing machine.
Haier washing machine error Err5, Error 5
Cause:
- This error indicates that the washing machine is unable to detect that the water tank is filled.
Solution:
- Check that hoses are connected to their intended positions and that the supply valves are fully turned ON.
- Ensure that hoses have no kinks or leakages.
- Don’t use flood-safe water inlet hoses as they prevent the washing machine from filling with too much water.
Haier washing machine error Err6, Error 6
Cause:
Apart from Err6 or Error 6, the error is also indicated as the door lock light will glitter 6 times with 4-second intervals.
- This error is a clear indication that the timing control silicon is faulty or damaged.
Solution:
- Seek professional help from a technician for the maintenance and service of your washing machine.
Haier washing machine error Err7, Error 7
Cause:
- The motor is overheating due to any electronic or technical issue.
- Motor overheat protection is not working properly.
Solution:
- Seek professional help from a technician for the maintenance and service of your washing machine.
Haier washing machine error Err8, Error 8
Cause:
- Water is going past the safe maximum level of the washing machine.
Solution:
- Check the water inlet valves and ensure that they are in place and good shape.
- Seek professional help from a technician for the maintenance and service of your washing machine.
Haier washing machine error E1
Cause:
- This error is reported by the washing machine when it is unable to drain all the water within its normal 4 minutes limit.
Solution:
- Clean the drain pump and its filters to remove dirt or any other thing blocking the water flow.
- Remove kinks and repair leaks in drain hoses.
- Make sure that water inlet valves are fully turned ON.
Haier washing machine error E2
Cause:
- This error occurs when the door is unable to close within 20 seconds of its normal limit.
Solution:
- Check if something is preventing the door from closing such as cloth.
- Clean the door locking mechanism and if it is damaged or broken, replace it.
Haier washing machine error E3
Cause:
- The washer is not balanced mostly because of too few clothes.
- It can happen if a towel, blanket, or multiple clothes are rolled into a ball and now sitting on one side of the washer.
Solution:
- Put some more laundry if there are too few clothes in the washing machine.
- Check laundry for any rolls, take it out of the washing machine, separate or lose the laundry, and put it back into the washer.
- Seek professional help from a technician for the maintenance and service of the washer.
Haier washing machine error E4
Cause:
- This error is reported by the Haier washing machine when water doesn’t reach its intended level within 8 minutes of its normal time limit.
Solution:
- Check and make sure that water supply hoses are properly connected to water inlet valves.
- Make sure that water hoses don’t have any kinks or leaks. Replace them if they are damaged.
Haier washing machine error E5
Cause:
- The water level sensor is faulty and not working properly.
Solution:
- Seek professional help from a technician to check the water level sensor, its wiring, and connections. Replace the sensor if needed.
Haier washing machine error E7
Cause:
- Different parts of the washing machine are unable to communicate with each other. This thing can happen due to any kind of issue in any part of the machine.
Solution:
- Seek professional help from a technician to check wiring and connections, and service your washing machine.
Haier washing machine error E8
Cause:
- This error is a warning by the washing machine that water is going past the normal level.
- This can happen because of issues in the NTC and main PCB.
Solution:
- Check the NTC resistance using a meter and make sure that it is consistent.
- Check the wiring and connections between NTC (Negative Temperature Coefficient) and the main PCB (Printed Circuit Board).
Haier washing machine error E11
Cause:
This error can occur when water is flowing into the washing machine tank in a very little amount or not at all. This can happen if:
- The faucet is opened.
- The water supply hose is clogged or frozen.
- Water inlet valves are not fully turned ON.
Solution:
- Check and make sure that the water faucet is closed and water is solely entering the washing machine tub.
- Check the water supply hose for any kinks or leaks, and replace the hoses if needed.
- Check and ensure that the water inlet is fully turned ON.
Turn OFF the washing machine and then turn it ON again after implementing the solution.
Haier washing machine error E12
Cause:
This error can occur if there is any kind of issue in the washing machine’s water drainage system.
- The drain hose’s height is more than the normal height limit of 100mm.
- The drain hose has kinks, leaks, or is blocked due to something stuck such as fiber scrap.
- The drain hose is too long for the water to come out forcefully.
Solution:
- Check and ensure that the height of the drain hose is adequate and it is not raised too much.
- Remove kinks and repair leaks in the drain hoses. Replace the hose if it is too damaged.
- Reduce the drain hose length to a normal range of about 3 feet.
Haier washing machine error E13
Cause:
- This error indicates a high level of lint build-up in the Haier washing machine tank.
Solution:
- Run a wash cycle without any clothes in the tank for removing lint.
- Put a small piece of cleaning cloth such as a dish towel in cold water along with 1 cup of white vinegar. The cleaning properties of white vinegar will break the lint into small pieces and in the end, will drain it out with the water.
Haier washing machine error F3, F4
Cause:
- Defective harness connections.
- Fault in the heater or its assembled parts.
- Some kind of issue with the main PCB (Printed Circuit Board) of the washing machine.
Solution:
- Check and ensure that the wiring, connections, and connectors between the PCB and heater assembly are in good shape.
- Check the resistance of the heater using a meter and it should be about 30Ω.
- Check the PCB and if it’s faulty, replace it.
Haier washing machine error F7
Cause:
- This error occurs if there is some issue in the circuit of the main motor.
Solution:
- Seek help from a professional technician to ensure that all wiring, connections, and connectors are in place. Repair or replace the electric parts if needed.
Haier washing machine error F9
Cause:
- The dryer sensor circuit of the washing machine is at fault.
Solution:
- Seek the assistance of a technician to check the dryer sensor circuit and repair or replace it as required.
Haier washing machine error CLR FLTR
Cause:
“CLR FLTR” is giving you a message to Clean Filters for better drainage of water from your washing machine:
- Water is not draining within its normal time limit of 6 minutes.
- Filters in the drain pump are clogged because of too much fiber scrap and dirt build-up.
- The drain pump is itself faulty and not working.
- The main PCB (Printed Circuit Board) of the washing machine is defective.
Solution:
- Check the drain hose for any kinks or leaks, and replace them if needed.
- Take the filters out and clean them thoroughly to remove fiber scrap and dirt.
- Check the pressure switch hose to ensure that it is opened and nothing is stuck inside.
- Check the wiring and connections of and between the drain pump and power PCB.
- Check the resistance of the drain pump using a meter. It should be about 224Ω.
Haier washing machine error FA
Cause:
The FA error on the Haier washing machine is reported due to multiple reasons. Major causes include:
- Some kind of issue in the circuit of the water level sensor.
- The pressure sensor hose or the pressure chamber is clogged mostly because of fiber scrap.
- The main or sub-PCBs (Printed Circuit boards) are defective.
Solution:
- Check for the wiring, connections, and connectors between the water level sensor and the display board of the washing machine.
- Check and ensure that the water level sensor, hose, and pressure chambers are all working fine.
- If you are still getting the error, replace the main PCB or the water level sensor.
Haier washing machine error FC0
Cause:
Multiple things can become a reason for this error on Haier washing machines. Some potential causes include:
- The washing machine is not getting any signal or feedback from the driver unit.
- The machine harness is defective or damaged.
- The display board or the main PCB (Printed Circuit Board) of the washing machine is faulty.
Solution:
- Look for an open or short circuit while making sure that the terminals are installed and inserted in their intended ports.
- Check the wiring and connections between the display board and the power board. Replace the display board if it is damaged.
- Check the main PCB for any fault and replace it, if needed.
Haier washing machine error FC1
Cause:
FC1 error can occur due to the following multiple reasons:
- The harness connection is faulty or damaged.
- The inverter board is defective.
- There is some issue or defect in the main PCB (Printed Circuit Board).
Solution:
There are many solutions and you need to implement them one by one until the error is not displayed anymore. Firstly, take a look at the LED light on the inverter board.
- If the LED light is OFF, check the voltage supply coming from the power board to the inverter board. If the voltage meter is not showing voltages, it means that the power board is faulty and needs replacement.
- If the LED light is ON, the main board is at fault. Repair or replace it as required.
- If the LED light is flashing, the inverter board needs to be replaced.
- Check the wiring and connections between the inverter and mainboards.
Haier washing machine error FC2
Cause:
The error can be caused due to reasons like:
- Damages in the harness connections.
- The display board is defective or completely damaged.
- Issues in the main PCB (Printed Circuit Board).
Solution:
- Check for an open or short circuit while making sure that the terminals are installed and inserted correctly.
- Check the wiring and connections between the display board and the power board. If damaged, replace the display board.
- If you are still getting the error, check the main PCB for any faults and replace it, if needed.
Haier washing machine error Fd
Cause:
- The dryer isn’t heating properly.
- The dryer heating mechanism is showing ill signs due to some fault.
Solution:
- Seek professional help from a technician for the maintenance and service of the washer.
Haier washing machine error FE
Cause:
- The main motor of the dryer is not working properly.
Solution:
- Seek professional help from a technician for the maintenance and service of the washer.
Haier washing machine error H
Cause:
This error can be shown on the Haier washing machine display due to the following reasons.
- The door of the washing machine is not opening.
- The water temperature in the washer is going beyond the 40°C limits.
Solution:
- Check for the water temperature sensor to ensure that it is working fine. You may need professional help to service your washing machines.
- Haier washing machines have the safety feature of not opening the door if the water inside the washer is too hot. So, the door will open as soon as the temperature comes down below the 40°C limits.
Haier washing machine error Unb
Cause:
- The clothes in the washing machine are unbalanced which mostly happens when some clothes trap together and sit on one side of the machine.
- The suspension spring of the washing is dull or broken.
- Shock absorbers are faulty and need service.
Solution:
- Slow down the spinning speed.
- Check the clothes and separate them if they are sitting in one place as a ball.
- Put some more clothes if there is too little laundry in the washing machine.
- Check the suspension spring and shock absorbers. If faulty, repair or replace them.
Haier washing machine error U3
Cause:
The error can occur due to multiple reasons such as:
- The washing machine is unable to spin and start the cycle.
- There is too much or too heavy laundry in the washer.
- There is a blanket, towel, or bed sheet rolled like a ball, and is now just sitting in one place in the washer.
- There are too few clothes in the washing machine.
Solution:
- Stop the washing cycle and start again.
- Turn OFF the washing machine for a few seconds and then turn it ON again.
- Take some clothes out of the washer to decrease some load on the washing machine motor.
- Check for rolled or trapped laundry, take it out, separate it or make it lose, and then put it back into the washing machine.
Add a few more pieces of clothes to the washing machine.
“Your home is a representation of yourself, and it should only be filled with clean items that you enjoy and use”
Professional cleaning expert